How to Clean Vacuum Hose | Improve Vacuum Performance

The vacuum is the most beneficial appliance in our home. We use it to clean from carpet to floor, upholstery, sofa, or any hard-to-reach areas. While you are enjoying so many advantages of using the vacuum, you should take proper care and maintenance of it. The vacuum hose needs regular care so that it gives a great performance. 

On the other hand, if neglect maintenance for a long time, the machine will be clogged, and altogether it will stop working. The vacuum hose is the most important component of the machine. The machine’s suction power comes through the hose and sucks all the dirt and debris. As the hose has a direct connection to dirt and debris, it is likely to be clogged after a few usages. 

But how to clean a vacuum hose properly? If you are unaware of the right way to hose cleaning, then follow our step-by-step guide. Obeying our guide, you can increase the vacuum lifespan. 

Why do you need to clean the vacuum hose?

A vacuum hose is also called a line or tube that is actually a durable rubber connection. It makes a route from the motor. The vacuum hose is a significant part of the machine. The dirt goes through this tube. Without proper cleaning, the vacuum hose tends to be blocked and malfunction. The hose also becomes stinky and decreases the suction power. 

Food pieces and pet hair are the common reasons for hose clogging. Many of us said to wait for clogged up then clean, but you shouldn’t wait for this. Make a regular routine to clean the hose. Cleaning on a regular basis, you will get superior performance from the vacuum. 

How many times should I clean in a month?

According to manufacturers, they recommend cleaning the vacuum hose once a month. But the period may be different depending on your usage. It does not mean that you are required to clean after every usage. 

The best way is to check inside the hose after heavy usage. If you inspect some obvious clogs then you must clean them immediately for further better performance. Again, do not wait for it to get clogged up. 

What are the signs of a clogged vacuum hose?

A clogged vacuum hose means bad performance. But it does not indicate that you need to replace the whole vacuum machine. Here are some obvious signs of a clogged vacuum hose:

  • The suction power will decrease.
  • The hose won’t pick up all the dirt and debris from the surfaces. 
  • The motor makes uneven noise.
  • The hose blowing dust. 
  • Bad smell coming from the hose. 

If you get a bad smell, there must be food pieces stuck on the hose. When you are having these issues, then understand the hose requires to be cleaned. A clogged vacuum hose leaks air and doesn’t pick dirt. 

How to Clean a Vacuum Hose?

When you have these issues, or you inspect some clogs or it is time for regular cleaning, you should prepare for hose cleaning. So follow our step-by-step guide below:

Things you will need

  • Dish soap or mild detergent
  • Baking soda 
  • White vinegar
  • Water
  • A thin and tough stick
  • Bottle cleaning brush. 

Step 1: Depart the hose from the vacuum machine

The first step is to separate the hose from the vacuum. But be sure, you have switched off and unplugged the vacuum from the electrical outlet. For your safety, you should be careful; otherwise, you have to suffer serious shock. 

Anyway, back to the separation process. Detaching method of the hose may vary according to its models and brands. Most vacuum has a twisting out, or press button system. But don’t ever force on the hose, it may damage the hose connection.

No model has a complex hose design, if you can’t detach it, there may be another system for detaching. If you don’t figure out the system then scan the user manual of the machine. You will surely figure it out. 

Step 2: Remove the visible clogs and debris

Now, look through the hose, you may see solid clumps and debris. It’s time to remove them. Place the hose on a flat surface like the floor or table. Use a thin and strong stick to insert into the hose and push the clumps out to bring outside. You can use the handle of the broom or mop as a stick. Make sure your vacuum hose is durable and lightweight; otherwise, there will be an unwanted hole by pushing too forcefully.  

Step 3: Wash the hose

In the hose, there will be a lot of sticking dirt to the inner folds and washing is the only way to remove them. Always wash the vacuum hose in the bathroom, don’t use the kitchen sink to wash. Or take a bucket and fill around four inches of water. Then add two tablespoons of dish soap or mild detergent to the water. 

The hose should totally submerge in the bucket water. Move the hose and let the water go through the tube and cleanse the material. Don’t use harsh chemicals to clean; it can damage the hose material. 

Step 4: Sanitize the hose

The vacuum hose picks up all the dirt and debris. Obviously, there will be a lot of bacteria and germs inside the tube. It requires being hygienic. Mix the baking soda and distilled white vinegar in the water. These two ingredients are the best DIY to get rid of bacteria without using strong bleaches. The acetic acid in the vinegar destroys the harmful virus. 

In a bowl, take two cups of vinegar, half a cup of baking soda, and two cups of water. Mix the ingredients well then pour it into the hose. You will see lots of fizzing which is quite enjoyable. 

Step 5: Utilize the bottle cleaning brush

If you don’t clean the vacuum hose for a long time, it will be dirty and there will be some stubborn grime inside the hose. Cleaning this grime is nearly difficult as it is inside the fold. A bottle cleaning brush can help you out. 

The bottle cleaning brush has rounded bristles which is the right tool to scrub lingering and grime. Choose a thin and long brush that can get into the middle of the hose. When you are done with one part then embed the brush into another part. 

Step 6: Rinse the hose

After doing a nice scrubbing, the hose needs to be rinsed out. Use high water pressure directly from the faucet so that it can clear all the grime and residue. Clutch it 

in a “U” shape and shake water around then flush it out. Give adequate rinsing to the hose to knock off all dirt. 

Step 7: Dry it before installing

Before installing the hose back into the vacuum, dry it properly. Hang it up to any hook and let move out all water from the inner holder. Give a quick shake to remove excess water. Leave the hose for several hours until it is not dried. 

Step 8: Back to the cleaning

After cleaning, rinsing, and drying properly, reinstall the hose into the machine. Follow the same way how you detach it. Hopefully, the machine will give better suction power when you turn it on. There will be no longer a low suction or bad smell. 

Frequently Asked Questions (FAQs)

1. Why does my vacuum smell bad?

If any food particles or organic components are stuck in the vacuum hose, it gets rotten and blows a bad smell. Moreover, you won’t clean the hose for a long time, it releases a bad smell. The bad smell indicates the hose needs a good cleaning. 

2. How to disinfect the vacuum hose?

There is a high chance of germ build-up in the vacuum hose, so it needs to be disinfected. Baking soda and vinegar combination is a great way to disinfect. In our guide, you will get the full process. 

3. How to deep clean a vacuum hose?

When you make up your mind to give a good and deep clean to the vacuum hose, our straightforward steps will assist you. Following this, you can properly clean the hose and improve the vacuum performance. 

Wrapping up 

Vacuum hose cleaning is an important job to improve performance. You must do this task once a month to enhance its longevity. Regular cleaning provides precise air movement and lets you clean your home effectively. This guide is the easiest way to clean the hose.

Leave a Comment